Data Stream Dissector (DSD) Kit Parts List
		     last revised 8/8/94 for v0.7

Notes   (<n> in the Parts List refers to the following notes)
----------------------------------------------------------------

<1>  When a quantity is shown in parentheses, that is the actual
     quantity supplied in the kit.

<2>  Resistor color codes:  If there is a silver or gold band at one
     end of the resistor, read off the color codes from the other end
     and ignore the silver or gold band.

<3>  The terms "axial" or "radial" refer to the lead style on the
     capacitor.

<4>  Quoted numbers are markings found on the part.

<5>  Resistors supplied with the kit have a Brown body color.
     Inductors supplied with the kit have a Green body color.
     The one exception is R17 which is a resistor with a Green body color.

<6>  Manufacturer: Crystal Semiconductor.

<7>  Manufacturer: Unitrode.

<8>  Manufacturer: Pulse Engineering.

<9>  Manufacturer: Toshiba.

<10> The PAL may be a National Semiconductor electrically erasable
     "GAL" device.  Other substitutions are also acceptable.
     The kit is supplied with a pre-programmed part.
     
<11> A 47uH inductor is an acceptable substitution.

<12> A 2N3907 transistor is an acceptable substitution.

<13> TIP32 or TIP32A or TIP32B are all acceptable substitutions.

<14> A 250uF capacitor is an acceptable substitution.

<15> "uF" and "uH" stand for microfarad and microhenry, respectively.

<16> T6 is not supplied in the kit.  It is optional.

<17> Material used for non-electrolytic capacitors should be
non-critical, i.e.  tantalum, metal film, polyester, polypropylene or
ceramic should all be OK.

----------------------------------------------------------------




       Data Stream Dissector (DSD) Kit Parts List (page 2 of 2)


Capacitors (16V minimum, except where noted) <3> <4> <15> <17>
----------------------------------------------------------------
C1-C6   6 (7)   0.01uF Ceramic                     (axial "103")
C7      1       10uF Electrolytic
C8-C13  6       0.1uF Ceramic                      (axial "104")
C14     1       0.047uF Polyester or Polypropylene (radial "473")
C15     1       220uF 25V Electrolytic  <14>
C16     1       0.033uF Polyester or Ceramic       (radial "333")

Inductors (50mA minimum) <5> <15>
----------------------------------------------------------------
L1      1       56uH   <11> (green blue black silver -- curved sides)
L2      1       5.1uH   (green brown gold silver -- straight cylinder)

Transistors
----------------------------------------------------------------
Q1      1       2N3906  <12>  (TO-92 package)
Q2      1       TIP32C  <13>  (TO-220 package)

Resistors (1/4 watt, 5% carbon or carbon film)  <5>  <1>
----------------------------------------------------------------
R1-R3   3 (4)   75 ohms       (violet green black)
R5-R16  12      5.1K ohms     (green brown red)
R17     1       8.2K ohms     (grey red red)
R18     1       560 ohms      (green blue brown)
R19-R22 3 (4)   360 ohms      (orange blue brown)
R23     1       330 ohms      (orange orange brown)
R24-R26 3       1K ohms       (brown black red)
R27-R30 3 (4)   91 ohms       (white brown black)

Miscellaneous
----------------------------------------------------------------
D1-D2   2       Red T 1 3/4 Round LED
D3      1       Yellow T 1 3/4 Round LED
D4      1       Green T 1 3/4 Round LED
P1      1       Octal (4x2) phono/RCA female panel-mount jack
O1      1       TORX176 Fiber Optic Receiver   <9>
O2      1       TOTX176 Fiber Optic Transmitter   <9>
T1-T6   5       PE65612 Pulse Transformer   <8> <16>
J1-J8   8       Jumpers (not supplied - use wire)

Integrated Circuits
----------------------------------------------------------------
U1      1       CS8412CP   <6>
U2      1       CS8402CP   <6>
U3      1       PAL22V10 CMOS pre-programmed with DSD v0.6 program <10>
U4      1       MC3486N
U5      1       MC3487N
U6      1       SN74HCT74N
U7      1       UC3835N    <7>
U8      1       10 Position SPST DIP Switch




		  DSD Mega Expansion Kit Parts List
		     last revised 8/8/94 for v0.7

Notes   (<n> in the Parts List refers to the following notes)
----------------------------------------------------------------

<2>  Resistor color codes:  If there is a silver or gold band at one
     end of the resistor, read off the color codes from the other end
     and ignore the silver or gold band.

<3>  The terms "axial" or "radial" refer to the lead style on the
     capacitor.

<4>  Quoted numbers are markings found on the part.

<8>  Manufacturer: Pulse Engineering.

<9>  Manufacturer: Toshiba.

<11> A 47uH inductor is an acceptable substitution.

<15> "uF" and "uH" stand for microfarad and microhenry, respectively.

<17> Material used for non-electrolytic capacitors should be
non-critical, i.e.  tantalum, metal film, polyester, polypropylene or
ceramic should all be OK.


----------------------------------------------------------------


Capacitors (16V minimum, except where noted) <3> <4> <15> <17>
----------------------------------------------------------------
C1-C6   1       0.01uF Ceramic                     (axial "103")
C8-C13  1       0.1uF Ceramic                      (axial "104")

Inductors (50mA minimum) <15>
----------------------------------------------------------------
L1      1       56uH   <11> (green blue black silver -- curved sides)

Resistors (1/4 watt, 5% carbon or carbon film)
----------------------------------------------------------------
R1-R3   1       75 ohms       (violet green black)
R17     1       8.2K ohms     (grey red red)
R19-R22 1       360 ohms      (orange blue brown)
R27-R30 1       91 ohms       (white brown black)

Miscellaneous
----------------------------------------------------------------
O1      1       TORX176 Fiber Optic Receiver   <9>
O2      1       TOTX176 Fiber Optic Transmitter   <9>
T1-T6   2       PE65612 Pulse Transformer   <8>